nomc www.vishay.com vishay dale thin film revision: 25-apr-17 1 document number: 60007 for technical questions, contact: thinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 molded, 50 mil pitch, dual-in-line thin film resistor, narrow body, surface mount network the nomc series features a standard 14 pins and 16 pins narrow body (0.150") small outl ine surface mount style. it can accommodate resistor networks to your particular application requirements. the networks can be constructed with passivated nichrome (sta ndard), or tantalum nitride (1) resistor films to op timize performance. note (1) available upon request. resistance value range and performance differs from passivated nichrome standard electrical specifications on datasheet, consult factory features ? standard 14 pins and 16 pins counts ? (0.150" narrow body) jedec ms-012 ? variation ab and ac ? rugged molded case construction ? excellent long term ratio stability ? ( ? r 0.015 %) ? low tcr tracking 5 ppm/c ? isolated and bussed schematics ? material categorization: fo r definitions of compliance please see www.vishay.com/doc?99912 note ? * this datasheet provides information about parts that are ? rohs-compliant and / or parts th at are non rohs-compliant. for ? example, parts with lead (pb) te rminations are not rohs-compliant. ? please see the information / tables in this datasheet for details typical performance schematics the 01 circuit provides a choice of 13 or 15 equal value resistors each connected between a common lead (14 or 16). custom schematics available. the 03 circuit provides a choice of 7 or 8 equal value resistors (14 or 16). cust om schematics available. note ? consult factory for additional values actual size absolute tracking tcr 25 5 absolute ratio tol. 0.10 0.05 available available nomc1401 or nomct1401 nomc1601 or nomct1601 nomc1403 or nomct1403 nomc1603 or nomct1603 standard resistance offering (equal value resistors) isolated (03) schemati c bussed (01) schematic 1 k ? 1 k ? 2 k ? 5 k ? 5 k ? 10 k ? 10 k ? 20 k ? 20 k ? 25 k ? 50 k ? 100 k ?
nomc www.vishay.com vishay dale thin film revision: 25-apr-17 2 document number: 60007 for technical questions, contact: thinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? available upon request. resistance value range and performance differs from passivated nichrome standard electrical specificat ions on datasheet, consult factory standard electrical specifications test specifications conditions material passivated nichrome (standard) tantalum nitride (ava ilable upon request) - pin/lead number 14, 16 - resistance range 100 ? to 50 k ? each resistor (bussed (01) schematic) - - 100 ? to 100 k ? each resistor (isolated (03) schematic) tcr: absolute 25 ppm/c (standard) - 55 c to + 125 c tcr: tracking 5 ppm/c (typical) - 55 c to + 125 c tolerance: absolute 0.10 % to 1 % + 25 c tolerance: ratio 0.025 % to 0.1 % + 25 c power rating: resistor 100 mw ((typical) (03) schematic) maximum at + 70 c 50 mw ((01) schematic) power rating : package 400 mw/500 mw maximum at + 70 c stability: absolute ? r 0.05 % 2000 h at + 70 c stability: ratio ? r 0.015 % 2000 h at + 70 c voltage coefficient < 0.1 ppm/v - working voltage 100 v max. not to exceed - operating temperature range - 55 c to + 125 c - storage temperature range - 55 c to + 150 c - noise ? - 30 db - thermal emf 0.08 v/c - shelf life stability: absolute ? r 0.01 % 1 year at + 25 c shelf life stability: ratio ? r 0.002 % 1 year at + 25 c p x r dimensions and imprinting in inches and millimeters dimension 14 16 inches millimeters inches millimeters h 0.235 5.969 0.235 5.969 e 0.154 3.911 0.154 3.91 o 0.340 8.363 0.390 9.906 a 0.063 1.60 0.063 1.60 e 0.050 1.270 0.050 1.270 b 0.015 0.381 0.015 0.381 c 0.008 0.203 0.008 0.203 l 0.025 0.635 0.025 0.635 a1 0.006 0.152 0.006 0.152 h 0.015 0.381 0.015 0.381 h x 45 a 1 a c l e b index area pin 1 locator o e h mechanical specifications resistive element passi v ated nichrome substrate material silicon body molded epoxy terminals copper alloy lead (pb)-free option 100 % matte tin tin lead option sn90 tin lead and lead (pb)-free finish plated
nomc www.vishay.com vishay dale thin film revision: 25-apr-17 3 document number: 60007 for technical questions, contact: thinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes (1) tolerance available 1k and up (2) preferred packaging code ordering information check list (customs) special requirements should be identified in advance, but as a minimum, you should have the following information ready. electrical mechanical 1. resistors, by value and tolerance 2. reference resi stor(s) and matching of which resistors to which reference resistors 3. referenc e by ratio 4. absolute temperature coefficient of resistivity 5. temperature tracking of subordinate resistors to reference resistor(s) 6. maximum operating voltage 7. resistor power ratings 8. operating temperature range 1. maximum allowable seated heig ht (from pc board to top of network) 2. special marking concerns 3. schematic pin out of package global part number information new global part nu mbering: nomc16031002buf global model (4 or 5 digits) pins schematic resistance tolerance and ratio tolerance packaging nomc (tin lead) nomct (lead (pb)-free) (e3) 14 16 01 = 13 or 15 ? bussed ? equal value ? resistors ? 03 = 7 or 8 ? isolated ? equal value ? resistors first 3 digits are significant figures and the last digit specifies the number of zeros to follow. example: 1002 = 10k 1003 = 100k abs. tol. ? ? a = 0.1 % (1) ? b = 0.1 % ? c = 0.25 % ? d = 0.5 % ? f = 1 % ? z = 0.1 % (1) ratio ? ? 0.05 % ? 0.1 % ? 0.1 % ? 0.1 % ? 0.5 % ? 0.025 % tape and reel t0 = 100 min., 100 mult t1 = 1000 min., 1000 mult (2) t3 = 300 min., 300 mult t5 = 500 min., 500 mult tf = full reel 2500 ts = 100 min., 1 mult uf = tubed historical part number example: nomc16031002z (for reference purposes only) nomc 16 03 1002 z series pins schematic resistance tolerance and ratio tolerance ct14 310 0 om 3zt1 0 n mc16 310 0 no 2buf 0
legal disclaimer notice www.vishay.com vishay revision: 08-feb-17 1 document number: 91000 disclaimer ? all product, product specifications and data ar e subject to change with out notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of th e products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product , (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all implied warranties, includ ing warranties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain types of applicatio ns are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular applic ation. it is the customers responsibility to validate tha t a particular product with the prope rties described in the product sp ecification is suitable for use in a particular application. parameters provided in datasheets and / or specifications may vary in different ap plications and perfor mance may vary over time. all operating parameters, including ty pical parameters, must be va lidated for each customer application by the customer s technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product could result in personal injury or death. customers using or selling vishay product s not expressly indicated for use in such applications do so at their own risk. please contact authorized vishay personnel to obtain writ ten terms and conditions rega rding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners. ? 2017 vishay intertechnology, inc. all rights reserved
|
